Singapore Air Conditioning Repair Service Guide
Menu

Air conditioning repair services glossary

Short, plain-English definitions of the terms you'll meet when choosing a air conditioning repair service provider in Singapore.

BTU and cooling capacity
BTU (British Thermal Unit) per hour is a measure of how much heat an air conditioner can remove from a room in one hour. One kilowatt equals about 3,412 BTU per hour, and one horsepower of cooling is roughly 9,000 BTU per hour.
Chemical overhaul
A chemical overhaul is a thorough air conditioner servicing method in which the indoor unit is fully dismantled so its parts, especially the blower wheel and evaporator coil, can be cleaned with chemical solutions. It goes well beyond a routine wash and is used to remove built-up grime, mould, and dust that normal servicing cannot reach.
Chemical wash
A chemical wash is an air conditioner cleaning method in which a chemical solution is applied to the indoor and outdoor coils and other internal parts to dissolve dirt, grease, and mould that ordinary cleaning leaves behind. It goes deeper than a routine service, which mainly clears filters and surface dust.
Condenser unit
A condenser unit is the outdoor part of a split or central air conditioning system that houses the compressor, the condenser coil and a fan. It releases the heat pulled from indoors into the outside air.
Drain pipe choke
A drain pipe choke is a blockage in the condensate drain line of an air conditioner, usually caused by algae, dust, or debris, that stops water from flowing out of the unit. The trapped water backs up and can leak into the room instead.
Energy label (tick rating)
The energy label tick rating is the Singapore NEA Mandatory Energy Labelling scheme's marking of one to four ticks on air conditioners, with more ticks indicating a more energy-efficient model. It is shown on the label attached to the unit and helps buyers compare power efficiency.
Evaporator coil
An evaporator coil is the indoor part of an air conditioning system that absorbs heat from room air as refrigerant evaporates inside it. Frost or dirt on the coil reduces its ability to absorb heat and can damage the system.
Fan coil unit
A fan coil unit is the indoor component of a central or chilled water air conditioning system, containing a coil that cools or heats air and a blower that pushes it into the room. It is distinct from the outdoor condensing equipment that rejects heat.
Gas top-up
A gas top-up adds a small amount of refrigerant to an air conditioner that has lost some charge, while a full recharge evacuates and refills the whole system. Low refrigerant pressure, read in psi on the service gauges, usually means the system has a leak.
General servicing
General servicing is the routine upkeep of an air conditioning unit, covering filter cleaning, a coil rinse, a check of the condensate drain, and a basic inspection of the system. It is done on a regular schedule to keep the unit cooling efficiently and to catch small faults early.
Inverter aircon
An inverter aircon is an air conditioner whose compressor motor runs at variable speeds to match the cooling load, instead of switching fully on and off. Non-inverter (fixed-speed) units cycle between those two states, which causes larger swings in temperature and power draw.
Non-inverter aircon
A non-inverter air conditioner uses a fixed-speed compressor that runs at full power or shuts off completely to reach and hold the set temperature. It is the older, simpler design that most inverter units replaced.
PCB (control board)
A PCB (control board) is the printed circuit board inside an air conditioner that receives signals from the remote and sensors and switches the compressor, fan, and valves. When it fails, the unit may power on erratically, show error codes, or stop running altogether.
R22 refrigerant
R22 (chlorodifluoromethane) is an HCFC refrigerant once widely used in air conditioners and heat pumps. It was phased out under the Montreal Protocol because it damages the ozone layer, and it now survives mainly in very old units.
Refrigerant leak
A refrigerant leak is the escape of coolant gas from the sealed circuit of an air conditioner, usually at a joint, fitting, or coil. Because the system depends on a fixed charge of refrigerant to move heat, a leak leads to weaker cooling and eventually a system that cannot cool at all.
Refrigerant piping
Refrigerant piping is the set of copper pipes, insulation and flare connections that carry refrigerant between the indoor and outdoor units of an air conditioner. It forms the closed loop through which heat is moved out of a room.
Thermostat
A thermostat is the control device that reads room temperature and tells an air conditioner when to run and when to stop. Its temperature sensor provides the reading that drives the on-off cycling of the compressor.
Vacuuming and leak test
A vacuuming and leak test is a two-stage check on an air conditioning system, where the technician first pressurises the lines with dry nitrogen to find leaks, then uses a vacuum pump to remove air and moisture before refrigerant is added.
What is a capacitor in air conditioning?
A capacitor in an air conditioner is an electrical component that stores and releases charge to give the compressor and fan motors the extra push they need to start and keep running. Run capacitors stay in the circuit during operation, while start capacitors deliver a short burst of energy at startup.
What is a compressor?
A compressor is the component of an air conditioning system that pressurises refrigerant and drives it around the cooling circuit. When it fails, the unit usually stops cooling entirely, making it one of the most important and costly parts to diagnose.
What is a System 1, 2, 3 multi-split?
A multi-split is an air conditioning setup where one outdoor compressor unit connects to two or more indoor fan coil units, with the number in the name (1, 2, 3) indicating how many indoor units it can run. In Singapore it is common in HDB flats and condominiums where space for separate outdoor units is limited.
What is R32 refrigerant?
R32 (difluoromethane) is a single-component hydrofluorocarbon refrigerant used in many current split air conditioners. It is classed as A2L, meaning mildly flammable, and has a lower global warming potential than R410A.
What is R410A refrigerant?
R410A is a blended HFC refrigerant used in many air conditioners, operating at noticeably higher pressure than older refrigerants such as R22. It is common in inverter units installed over the past couple of decades, and it needs equipment and gauges rated for its pressure.